Designed to provide uncompromising video quality at incredible distances, the Beam H.264 transmitter is perfect for ENG backhaul and moving vehicle applications
Transmitting over the unlicensed 5GHz band, Beam can attain distances up to 2500ft, perfect for ENG crews feeding full HD video back to an OB van.
Pristine Video Quality
Beam utilizes H.264 compression (Main profile) and can stream at up to 15 Mbps over its wireless link with just 2 frames of latency. When connected to a LAN, the device can stream up to 30 Mbps.
Built for Broadcasters
With 3G-SDI I/O and your choice of Gold- or V-mount battery plates, Beam seamlessly integrates with all popular professional cameras. An OLED is built-in for quick device configuration and the full duplex RS-422 port offers remote camera control.
Beam can stream to up to 4 receivers simultaneously, allowing you to send your feed to multiple destinations without any loss in video quality or added delay.
Beam supports both the RTSP and MPEG-TS protocols. Beam decoders can also act as an RTSP server, which will re-stream your video feed directly to a local computer.
Beam features a dedicated bi-directional IFB channel, which allows a news operations center to speak directly to the camera operator in the field.
Beam’s serial RS-422 port allows you to remotely control compatible PTZ cameras with a selectable baud rate up to 115.2 k/bits.
|Video Compression||H.264 Baseline Profile Level 4.2 with de-interlacing|
|System Latency||90 - 110 millisecond delay between Transmitter and Receiver|
|Wireless range||2500ft +- 200ft|
|Digital Video In/Out||SD-SDI, HD-SDI, 3G-SDI|
|Video Port||TX: SDI input and looped Output, RX: SDI output|
|Supported Video Resolutions||SMPTE244||480i59.94 (NTSC), 480i60 (861-D)|
|SMPTE 296M||720p23.98, 720p24, 720p25, 720p29.97, 720p30, 720p50, 720p59.94, 720p60|
|SMPTE 274M||1080i50, 1080i59.94, 1080i60, 1080PsF23.98,1080PsF24, 1080PsF25, 1080PsF29.97, 1080PsF30, 1080p23.98, 1080p24, 1080p25, 1080p29.97, 1080p30, 1080p50, 1080p59.94, 1080p60|
|SDI Compliance||SMPTE 259M BI.656||SDTV Digital Signal/Data Serial Digital Interface|
|SMPTE 292M BT.1120||1.5Gb/s Signal/Data Serial Digital Interface|
|SMPTE 425M||3Gb/s Signal/Data Serial Digital Interface|
|SMPTE 299M||16bit Digital Audio Format for SMPTE 292M|
|SMPTE 352M||Video Payload Identification for Digital Interfaces|
|Bitrate||RTSP Server||Up to 30Mbps|
|MPEG2-TS Server||Up to 15Mbps|
|Main Digital Audio In/Out||TX/RX||SDI embedded audio: 48kHz 16-bit stereo linear PCM|
|Main Analog Audio Out||RX||48kHz 16-bit stereo linear PCM with mini stereo phone output jack|
|Talk-Back Analog Audio In/Out||RX/TX||8kHz 16-bit stereo linear PCM with mini stereo phone input/output jack|
|Radio Power||Aggregate Power: 150mW (22dBm), 50mW (17dBm)/antenna|
|Radio standard||IEEE 802.11a/n: OFDM|
|Frequencies||U-NII-1 (5.15-5.25 GHz), U-NII-3 (5.725-5.85 GHz)|
|Antenna||3T x 3R MIMO, 3 antennas per WiMi6200TW/W1Mi6200RW|
|Security||802.1x, 802,11i, WPA2, WPA and WEP 64/128 TKIP 128bit AES|
|WPS||Wireless Protected Setup for easy set up and security configuration|
|Ethernet LAN||10/100 BASE-TX, RJ-45 jack|
|Multicast||WiFi: Up to 4 Receivers|
|LAN: No limit on number of receivers|
|External Control||Full duplex RS422 serial port|
|USB||Factory reset, IP configuration or firmware upgrade without PC|
|Power Input/Consumption||DC 7V-17V, 12 Watt|
|Dimensions (H x W x D) (mm)||170 x 105 x 28 each board assembly (TX or RX)|
|Weight (g)||TX: 990g
|Operating Temperature||0 deg C to 50 deg C|